I couldn't help but chuckle. This amplifier does not come with the original box, manual, or bass knob. This test was a quick plug and play situation, similar to what you would find in a car. I'd like to know where you heard any of that. What does your electrical constsist of? I know they are underrated, and alot of people like them because they can run them below 1 ohm. Does your 5000 watt amp really do 5000 watts? I have tried to adjust the crossover on the amp, I have played with the bass settings.
Also what kind of sound quality do they put out? These subs are fully loaded with each being in its own 2. This amplifier is in rough cosmetic condition, with some deep gouges. Sundown's reputation speaks for itself. Product Description: This is a large monoblock amplifier made by Sundown Audio. I guess it's a matter of how long you want them to be around, and how hard you plan to drive them. I think sundowns worth the money. This amplifier has been mechanically refurbished and stress tested and is fully functional.
I'll probably get one someday. And what are the settings on your 3500d set to? The refurbished amp I recieved was almost spotless and looks and functions like brand new. Maybe I should just go with two 12 inch btls instead and port them. I assume that lpf is low pass. Add all this to our soft parts and tooled frame and you have the perfect subwoofer we call the Zv. And what are the settings on your 3500d set to? This process also helps us make a stronger more reliable motor design. I am running this sub in a sealed box so I have the subsonic filter as far down as it can go.
Sundown's future has never been brighter due to the potential we can achieve with these baskets. Then of course I upgraded the hot and ground wires coming off of the alternator to zero gauge along with the rest of the big 3. I guess I am just looking for the best amp here which could match these subs perfectly at a 1 ohm mono load. I think for what you want and the power your using, bls or btls in a ported enclosure would be a better choice. We do our best to take care of people. They are capable of holding up to 12 inch spiders, and up to 5 inch voice coils in the base.
Well considering you went from 1000 watts to 3500 watts, sound quality will be lost since it seems like you were looking for more output when upgrading amps. That is set to 80 hertz from the head unit and left wide open on both amps since I set it on the head unit. The products are 100% fully functional, new products but they have minor cosmetic issues. I have zero gauge ran back to the amps and also have 4 1. A big thanks to The Amp Lab for the service you guys provide! Rockford used a 4 volt gain for those power amps while this sundown amp has a 6 gain setting.
Product Description: This is a large monoblock amplifier made by Sundown Audio. This amplifier does not come with the original box, manual, or bass knob. And the amps are pretty expensive as well, some people say they are the best, while others say they are overpriced. See the pictures for a full description of condition. I'd set the lpf on the amp to 80hz as well, I'd rather rely on it's crossover then the headunits, or use both Just for quicks when playing music turn the lpf and see if it sounds any better? This amplifier is in rough cosmetic condition, with some deep gouges. What does your electrical constsist of? We start with an idea, then to a sketch, to a functioning 3D model, then finally a prototype.
What settings should I play with? Because of the aforementioned blemishes they are offered to you at a discount. Our amplifiers are not just built for power though, they are designed for the discerning listener who needs hefty amounts of power for subwoofer duty. I have zero gauge ran back to the amps and also have 4 1. I think for what you want and the power your using, bls or btls in a ported enclosure would be a better choice. Well considering you went from 1000 watts to 3500 watts, sound quality will be lost since it seems like you were looking for more output when upgrading amps.
Shortly all of them will be new 1500D being tooled up, 1000D being replaced by new 1200D board, 2000D replaced by new 2500D board, etc, etc. That was set to off on the bd amps and is set to 10 hertz on the sundown amp or as low as it can go on the sundown amp. This amplifier is in okay cosmetic condition, but does have some scratches. With the bds I wired the subs at 4 ohms with bd sync which did not match those bds the best since that made them capable of 1500 watts rms at 4 ohms. From the beginning to end no detail gets over looked. I have zero gauge ran back to the amps and also have 4 1.